Exam Code : 300-410
Exam Name : Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
Vendor Name :
"Cisco"
300-410 Dumps
300-410 Braindumps
300-410 Real Questions
300-410 Practice Test
300-410 Actual Questions
killexams.com
Implementing Cisco Enterprise Advanced Routing and Services (ENARSI)
https://killexams.com/pass4sure/exam-detail/300-410
Question: 571
While troubleshooting connectivity issues to a router, these details are noticed:
Standard pings to all router interfaces, including loopbacks, are successful.
Data traffic is unaffected.
SNMP connectivity is intermittent.
SSH is either or disconnects frequently.
Which command must be configured first to troubleshoot this issue?
Show policy-map control-plane
Show policy-map
Show interface inc drop
Show ip route
Answer: A
Question: 572 Refer to the exhibit.
Which routes from OSPF process 5 are redistributed into EIGRP?
E1 and E2 subnets matching access list TO-OSPF
E1 and E2 subnets matching prefix list TO-OSPF
only E2 subnets matching access list TO-OSPF
only E1 subnets matching prefix listTO-OS1
Question: 573
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?
Multi-paths eibgp 2
Maximum-paths ibgp 2
Multi-paths 2
Maximum-paths 2
Question: 574
Which security feature can protect DMVPN tunnels?
IPsec
TACACS+
RTBH
RADIUS
Question: 575
Which command is used to check IP SLA when an interface is suspected to receive lots of traffic with options?
show track
show threshold
show timer
show delay
Question: 576
Users were moved from the local DHCP server to the remote corporate DHCP server. After the move, none of the users were able to use the network.
Which two issues will prevent this setup from working properly? (Choose two)
Auto-QoS is blocking DHCP traffic.
The DHCP server IP address configuration is missing locally
802.1X is blocking DHCP traffic
The broadcast domain is too large for proper DHCP propagation
The route to the new DHCP server is missing
Question: 577
Drag and Drop Question
Drag and drop the address from the left onto the correct IPv6 filter purposes on the right.
Question: 578
Refer to the exhibit.
An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 losses reachability with the router R3 Fa0/0 interface.
The route has changed to flow through route R2.
Which debug command is used to troubleshoot this issue?
debug ip flow
debug ip sla error
debug ip routing
debug ip packet
Answer: C
Question: 579 Refer to the exhibit.
A router receiving BGP routing updates from multiple neighbors for routers in AS 690.
What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.10.1?
The local preference value in another neighbor statement is higher than 250.
The local preference value should be set to the same value as the weight in the route map.
The route map is applied in the wrong direction.
The weight value in another statement is higher than 200.
Which configuration enables the VRF that is labeled `’inet” on FastEthernet0/0? (A)
(B)
(C)
(D)
Option A
Option B
Option C
Option D
Answer: D
Question: 581 Refer to the exhibit.
During troubleshooting it was discovered that the device is not reachable using a secure web browser.
What is needed to fix the problem?
permit tcp port 465.
permit tcp port 443
permit udp port 465
permit tcp port 22
Answer: B
Question: 582 Refer to the exhibit.
Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours
per day.
Which action fixes the issue within the current resources?
Configure the DHCP lease time to a bigger value
Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool
Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool
Configure the DHCP lease time to a smaller value
White working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device.
Why is the image not uploading?
The device has lost connectivity to Cisco DNA Center.
The software image for the device is in bundle mode
The software image for the device is in install mode.
The device must be resynced to Cisco DNA Center
Question: 584
Drag and Drop Question
Drag and drop the MPLS terms from the left onto the correct definitions on the right.