Latest DES-2T13 Practice Tests with Actual Questions

Get Complete pool of questions with Premium PDF and Test Engine

Exam Code : DES-2T13
Exam Name : Specialist - Cloud Architect, Cloud Infrastructure
Vendor Name : "DELL-EMC"







DES-2T13 Dumps DES-2T13 Braindumps

DES-2T13 Real Questions DES-2T13 Practice Test DES-2T13 Actual Questions


killexams.com


DELL-EMC


DES-2T13


Specialist - Cloud Architect, Cloud Infrastructure


https://killexams.com/pass4sure/exam-detail/DES-2T13



Question: 67

You are analyzing the performance data to avoid oversizing of a CI solution. What date and time frame should you use?


  1. Average production time over multiple days

  2. Peak production times over multiple days

  3. Average production time over a single day

  4. Peak production times over a single day




Answer: D



Question: 68

In a cloud design, an architect has defined a separate trust zone for host management. The hosts will be running open source hypervisors. What should be included in the design deliverables to support this separate trust zone?


  1. Federated authentication source and preferred QoS network settings

  2. Isolated management network and a federated super-user account

  3. Separate PKI and encrypted CMP portal access

  4. Separate PKI and a separate authentication source


As a cloud architect, you are designing a CI solution to ensure that you isolate specific workloads for security. What should you design for?


  1. High Availability

  2. Fault Tolerance

  3. Multi-tenancy

  4. Redundancy




Answer: B



Question: 70

Which design consideration applies to object storage?


  1. Multi-tenancy is supported through file and directory permissions

  2. It is best suited for high performance and low latency applications

  3. A RAID controller on the host computer handles redundancy

  4. A common authentication mechanism is accessible by all tenants




Answer: B



Question: 71

You are a cloud architect responsible for designing a multiple availability zone configuration for the organization’s geographically dispersed clouds. You must provide the ability for services to survive a failure at the data center or site level. The primary requirement is to provide for automated site recovery. What is a key consideration for automating the setup, failover, and recovery of services at the remote site?


  1. When implementing automated site recovery, you must have automated orchestration of site failback processes

  2. The number of storage volumes in the DR site must be identical in number and size to the primary site.

  3. The recovery site must have sufficient available capacity to host workloads after a disaster at the primary site.

  4. The DR site must contain the same vendor hardware as the primary site.


You are designing a cloud backup solution. Consider the following requirements when sizing the backup target:

. Total amount of data to be backed up = 2 TB (2000 GB)

. Full backup once a week

. Retention period for full backups = 2 months

. Daily incremental backups (assuming an average 10% change in data)

. Retention period for incremental backups = 1 month

. No Compression or deduplication

. Number of backup copies = 1

What is the total capacity, in GB, required for the backup target to accommodate the backups?


A. 13, 200

B. 16, 000

C. 21, 200

D. 26, 400




Answer: C



Question: 73

You are designing a cloud to support an Oracle OLTP environment. What is the recommended read/write ratio to use in this environment?


  1. 2 to 1

  2. 3 to 1

  3. 4 to 1

  4. 5 to 1




Answer: D



Question: 74

An organization wants to deploy cloud applications using block storage. The architect has included a HCI solution in the cloud design. Which requirements must have led to including this solution in the design?


  1. Acquire additional storage array; Combine storage and application processing using a spine/leaf topology

  2. No additional storage arrays to be acquired; Separate storage processing from application processing

  3. No additional storage arrays to be acquired; Combine storage and application processing on each node

  4. Acquire additional storage array; Combine storage and application processing using a full mesh topology




Answer: A