FCESP Dumps FCESP Braindumps
FCESP Real Questions FCESP Practice Test FCESP Actual Questions
killexams.com Fortinet FCESP
Fortinet Certified Email Security Professional
https://killexams.com/pass4sure/exam-detail/FCESP
none of the above
In an LDAP query, which variable can be used to identify the full email address?
$u
$m
$g
$s
Which CLI command was used to generate the output shown below: Version: FortiMail-400B v4.0,build0103,091223 (GA Patch 1) Virus-DB: 11.551(03/05/2010 01:02)
Serial-Number: FE400B3M09000140 BIOS version: 00010010
Log disk: Capacity 92 GB, Used 32 MB ( 0.04%), Free 92 GB Mailbox disk: Capacity 371 GB, Used 277 MB ( 0.08%) , Free 370 GB Hostname: server
Operation Mode: Server HA configured mode: Off HA effective mode: Off Distribution: International Branch point: 103
System time: Fri Mar 5 15:04:04 2010
diag system top
get sys performance
get sys status
diag netlink neighbor list
What is the outcome of the following CLI commands executed on a FortiMail unit operating in Transparent mode?
config system interface edit port2
set bridge-member disable end
Interface port2 is administratively down.
Interface port2 is removed from the transparent bridge.
Interface port2 is added to the transparent bridge.
Consider the proxy configuration shown in the exhibit.
***Exhibit is Missing***
A FortiMail unit is configured to protect the domain internal1.lab 192.168.11.101. All emails from IP 192.168.5.1/32 are relayed through an Access Control Rule.
An SMTP session from 192.168.5.1 to 192.168.11.102 (internal2.lab) is received on port1. Which statement best describes how the FortiMail unit will handle the SMTP session?
The SMTP session will be handled by the incoming proxy.
The SMTP session will be bridged without inspection.
The SMTP session will be inspected.
The SMTP session will be relayed to the IP 192.168.11.102.
The SMTP session will be rejected.
On a FortiMail unit operating in Transparent mode, which of the following parameters determines the direction of an SMTP session?
The destination IP address
The source IP address
The recipient domain address
The source domain address
When inspecting and delivering mail messages, which of the following steps could be taken by a FortiMail unit operating in Transparent mode?
Inspect for viruses.
Inspect content of the message payload.
Inspect for spam.
Perform a routing lookup to decide the next hop MTA.
Which of the following statements is true regarding an Active Passive HA configuration?
Different hardware models can be used to form a cluster.
The administrator can manage the slave unit only through the master unit.
Units operating in Transparent mode cannot be used to form a cluster.
The mail data and MTA queues can be synchronized between master and slave units.
A maximum of two FortiMail units can be used to form a cluster.
Which High Availability mode should an administrator choose to provide increased processing capabilities?
Active-Passive
Config-Only
Load-Balance
Standalone Answer: B QUESTION: 80
How can a FortiMail administrator retrieve email account information from an LDAP Server instead of configuring this data manually on the unit?
Configure the LDAP profile sections "User query options" and "Authentication" then associate the profile to the domain that is locally configured.
Configure the LDAP profile sections "Authentication" and "User Alias Options" then associate the profile to the domain that is locally configured.
Configure the LDAP profile sections "User query options" and "Authentication" and associate the profile to an incoming Recipient-based policy.
This operation is not supported. The administrator has to configure the user email accounts manually.
Which operational mode allows the FortiMail unit to operate as a full featured mail server rather than just a mail relay agent?
Server Mode
Transparent Mode
Gateway Mode
High Availability Mode